Improving Mud Motor Rotor Performance
Better Power Section Rotors Produced Faster
Leistritz, the machine tool builder most known for whirling machines, has collaborated with several well drilling equipment and tooling companies to improve manufacturing and find a solution to machining problems long associated to Power Section Rotors. These rotors connect directly to the drill bit in directional drilling for oil and gas discovery deep below the earth’s surface. The power section is a “positive displacement mud motor” combined with directional technology to steer the drill motor using tilting joints and sophisticated, telemetric, sensors. The motor converts the drilling fluid’s hydraulic energy into mechanical energy in the form of torque and rotational speed. This conversion is accomplished through the use of a spiral rotor that fits into a stator of similar shape, to form a tight seal. These systems are now capable of drilling within ±0.15° over depths to 18,000 ft. The rotors within the mud motors are called power section rotors, which are typically 5, 7 or 9 lobed with smooth spiral profiles in lengths as long as 8m with long leads of up to 40”. Fit snugly into an elastomer stator having one additional lobe contour with the same lead creates a moineau style progressive cavity positive displacement rotary drive unit. When the water based drilling fluid or “mud” is pressurized at the surface and pumped down the hole to the power section an extremely high torque low rpm drive is created to rotate the rock crushing drill bits.
milling cutter need replacing or indexing several times during the multiple shift operation of each rotor. This and continuous measurements by the operator in the middle of a rotor create unacceptable non-productive time.
Leistritz, developed an application specific solution by combining an existing heavy-duty machine base with a newly designed high performance, multi-axes drive head. This drive head is capable of both side milling and hobbing. The fundamental idea of hobbing is new to the industry and opens the door for shorter cycle times and much improved profile quality. In effect, these rotors are handled as very long gears, but the low number of lobes or teeth creates unique challenges for the hob tooling and machine tool.
A 30HP spindle with high tooth load hob designs guarantee speed and surface finishes previously unattainable. The 17-4PH stainless steel rotors are machined in a single pass using a large diameter hob (up to Ø10”) with a face-width of 8”. Superior hob life is achieved by using continuous diagonal hobshift to utilize the entire hob face during the cut of each rotor. So a rotor can be hobbed in a single non interrupted cutting pass with straightness less than 0.002”. A variety of hob materials and coatings have been tested to maximize the hob life and thus reduce the cost per piece.
The goal of producing four 315” long rotors per hob sharpening has been reached and in some cases exceeded. With 15 sharpenings permissible for each hob the process has proven to be very economical. The long lead of these rotor designs requires special solutions for supporting them while machining.
Leistritz uses CNC servo controlled, self centering, follower rests both for the raw material in front of the cut and the finished rotor behind the cut to achieve vibration free cutting.
Manufacturers of mud motors are experiencing hobbing cycle times less than half those of milling while also saving most of the time required to polish. In many cases polishing is eliminated and the rotors go straight to chrome plating.
The hobbing process also produces a profile exactly to the design specifications within ±0.001” and the profile is no longer deviated by the polishing process. The better profile tolerances lead to better drill motor performance in both consistency and torque.
Programming of the hobbing process is done at the machine by the operator since only a few critical parameters are needed to determine the necessary rotor criteria.
To reduce the learning curve to manufacturers of these rotors, Leistritz has kept milling as an secondary alternative within the machine tool function. The flexibility of milling allows manufacturers to maintain their known process and add hob tooling as desired for their more commonly produced sizes. The improved rigidity and spindle speed of the Leistritz machine accommodates accelerated cutting speeds & feeds to reduce milling cycle times by 30-40%. When milling, Leistritz has a convenient software package to generate the profile contour and to optimize the feedrate calculations by maintaining a constant chip thickness over the spiroid contour thus improving cycle times.
In addition, the Leistritz Power Mill machine can use CNC programs of existing equipment to continue side milling for even greater flexibility. The advantage here is the Power Mill machine is capable of 800 rpm for future tooling developments such as ceramic cutting tools.
Leistritz products, designed and built in Germany, are sold, supported with spare parts and serviced by
Leistritz Corporation, 165 Chestnut St. Allendale, NJ 07401 tel: 201 934-8262
Leistritz is a machine tool builder offering Internal and External whirling solutions, Rolling & Burnishing Equipment and hydraulic Keyseating machines.
Leistritz LWN-300 Power Mill Power Section Rotors Video